Parts & Accessories

Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.

Polyurethane pads with diamond plate traction pattern allow riders to customize their pedals for a perfect interface with any shoe. - Kit includes eight 1mm traction pads and eight 2mm traction pads

Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs

Crank Brothers' Tread Contact Sleeves shim the area between the pedal and your shoes' tread so there is no rocking or play when you're clipped in. They provide a solid platform to put down all your power! They work with either your Eggbeaters or Candy pedals, and each includes 1mm, 2mm, and 3mm shims.

Crank Brothers' 5050 Pin Kit includes fifty 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.

Engineered to optimize the interface between the pedal and shoe for ultimate performance and power transfer. The kit includes: - 8 × 1mm traction pads - 8 × 2mm traction pads Compatible with: - Candy 7 & 11 - Model years 2016 – present

Engineered to optimize the interface between the pedal and shoe for ultimate performance and power transfer. The kit includes: - 8 × 1mm traction pads - 8 × 2mm traction pads Compatible with: - Mallet E - Model years 2016 – present

Everything you need to keep those Crank Bros pedals spinning freely is found in their Pedal Rebuild Kit. Each kit includes parts and instruction to rebuild one pair of Crank Bros. pedals.

Your pedals like to be pampered. The Crank Brothers Pedal Refresh Kit gives you everything you need to keep them happy. Pedal Refresh Kit includes: -Enduro catridge bearings - Igus LL-glide bearings - Double seal system (internal and external seals) - Hex alloy end caps - O-rings - Nuts - Sleeve bushings - Bearing removal tool Compatible with the following pedals (2010-present): - Eggbeaters - Candys - Mallets - 5050s

A revolution in performance and reliability. - The kit includes premium internal components: - Inner spindle seal x 2 - Outer spindle seal x 2 - Inner Igus solid bearing x 2 - Outer Enduro cartridge bearing x 2 - Spindle nut x 2 - Outer bearing carrier x 2 - Compatibility: Doubleshot (2016), Doubleshot 2 (2017+), Soubleshot 3 (2017+)

A revolution in performance and reliability. The kit includes premium internal components: - Enduro catridge bearings - Enduro sealed needle bearing - Double seal system (internal and external seals) - Hex alloy end caps - O-rings, nuts - Sleeve bushings - Bearing removal tool

A revolution in performance and reliability. The kit includes premium internal components: - Inner bearing o-ring x 2 - Spindle seal x 2 - Outer Igus solid bearing x 2 - Inner Igus solid bearing half x 4 - Bearing Retainer Bolt x 4 - Outer o-ring x 2 - Grease port screw x 2 - Compatibility: Stamp (2016), Stamp 7 (2017+), Stamp 11 (2017+)

Cleats with a more forgiving 10-deg release. - Optimized for novice riders or those new to clip-in pedals - 10-deg release angle makes it easier to unclip - 2-hole bolt pattern for mountain bike shoes - Plastic spacing shims included - Compatible with all Crankbrothers clip-in pedals

Crank Brothers' Premium MTB Cleats are perfect for your Crank Brothers Eggbeater, Candy, Acid, Smarty, Mallet, and Quattro pedals. They're made from solid brass for crisp entry and exit, and top-notch durability. - SPD compatibility - Weight (pair): 30g - Float: 6 degrees - Release angle: 15 or 20 degrees

Crank Brothers' Quattro 3-Hole Cleats are the perfect cleats to use with your 3-hole compatible road shoes and Crank Brothers pedals. They're made from solid brass for crisp entry and exit, and durability.

Crank Brothers' Zero Float Cleats offer no pedal float for greater pedaling efficiency. They're made from solid brass for crisp entry and exit, and top-notch durability. - Weight (pair): 30 grams - Shoe compatibility: SPD - Release angle: 15 degrees

Widen your Q-factor to 57mm. - Long spindles are 5mm longer than standard. - The kit includes: 1 pair long spindles + refresh kit (Enduro cartridge bearings, igus ll-glide bearings, DSS double seal system: internal and external seals, hex alloy end caps, o-rings, nuts, sleeve bushings, & bearing removal tool). - Compatible with: Eggbeater, Candy, Mallet, 5050, Double shot, model years 2010-present - Weight: 112g per pair - Spindle material: forged SCM 435 chromoly steel - Q-factor: 57mm

The ultimate weight-saving upgrade.  - The kit includes: 1 pair titanium spindles + refresh kit (Enduro cartridge bearings, Igus ll-glide bearings, DSS double seal system: internal and external seals, hex alloy end caps, o-rings, nuts, sleeve bushings, & bearing removal tool). - Compatible with: Eggbeater, Candy, Mallet, 5050, Double Shot, model years 2010-present - Weight: 60g per pair - Spindle material: 6al/4v titanium - Max. rider weight: 200lb/90kg - Q-factor: 52 mm